The Peregrine series is notable for its sleek design and superior performance. The low-profile, streamlined housing encompasses an ultra efficient reflector and two Xenon lamps delivering unbelievable center-to-center spacing. Equipped with the optional dual-mode illumination feature, the Peregrine provides lighting not only during power outages, but also functions during normal conditions with a long-life, 5 watt LED lamp. The die-cast aluminum housing is offered in a wide range of colors to complement any interior and blend in with the most sophisticated decor. The sturdy housing is also fully gasketed making this unit ideal for extreme outdoor environments.

This decorative fixture is suited for indoor or outdoor locations.

• Low profile, slim lines - measures only 6.6'' x 9.5''
• Fully gasketed housing, rugged die-cast body and UV-resistant lens makes the unit suitable for cold, wet indoor/outdoor locations.
• Brilliant Xenon lamps for emergency mode, Optional White LED's allow the unit to function as a normal light.
• Optional Exterior package: UL listed for wet and cold location. Operating temperature: -20C to +40C (-4F to + 104F)
• Two high-output Xenon lamps with an impact and UV resistant polycarbonate lens combined with a patent-pending reflector deliver an incredible center-to-center spacing. The vacuum-plated die-cast reflector has been designed to provide an evenly distributed illumination pattern for corridors, up to 6' wide, and is built to last.
• The durable cast aluminum housing is finished with textured polyester powder coat paint. Available in four colors: off white, black, platinum gray and dark bronze.
• Self-powered units come with dual-input 120/277Vac, 60Hz. Chargers include low voltage disconnect to prevent deep discharge, battery lockout to prevent battery drain prior to energizing the utility power, brownout protection which will automatically switch into emergency mode if the utility power falls below 80% of nominal, and battery reverse polarity protection.
• The unit can be installed on various junction boxes with a universal mounting pattern, and can also accept a surface mount cable via the rigid conduit entry provision on the top of the unit.

The Peregrine Series comes complete with a 3-year full warranty (excluding fuses and incandescent lamps). The units are made of durable cast aluminum housing, finished with textured polyester powder coat paint. Four colors are available: off white, black, platinum gray and dark bronze. The vacuum-plated die-cast reflector will last over time. The lens is made of an impact and UV resistant polycarbonate. The unit can be installed on various junction boxes with universal mounting pattern. It can also accept a surface mount cable, via the rigid conduit entry provision on the top of the unit.

Peregrine Series units are furnished with two high-output Xenon lamps for emergency lighting. These lamps, combined with a patent pending reflector, deliver an incredible center-to-center spacing. The reflector has been designed to provide an evenly distributed illumination pattern for corridors, up to 6' wide.

All self-powered units come with a dual-input 120/277Vac, 60Hz. Chargers also include low voltage disconnect to prevent deep discharge, battery lockout to prevent battery drain prior to energizing the utility power, brownout protection which will automatically switch unit into emergency mode if the utility power falls below 80% of nominal and battery reverse polarity protection. Lead-Calcium models are equipped with Pulse Charge circuitry that promotes long battery life and excellent performance. This current limiting charger will minimize energy consumption. Nickel Metal Hydride Models are equipped with the non-audible version of the Self Diagnostics system. This charger is a self-test and self-diagnostic charger. It will monitor and indicate any of the following failures: battery disconnect, battery, charger and lamp failures. The unit will perform a periodical self-test, of minimum 30 seconds every 30 days, 30 minutes every six months and 90 minutes annually. Discharge test can also be initiated manually.

The dual-mode illumination feature enables the Peregrine to provide lighting not only during power outages, but also in normal conditions. This is achieved with a secondary light source, a long-life, 5-watt power LED lamp dedicated to normal lighting. When equipped with this feature, the equipment includes two independent circuits, electrically isolated from each other: the standard input for emergency lighting and a secondary input for normal lighting. The secondary input can be connected to a regular AC line that may include an electric switch.

The Peregrine is available in several configurations:

• Regular Interior package is a cost efficient solution equipped with Lead-Calcium battery.+20C to +30C (+68F to +86F)
• Exterior package: designed for a wide range of temperature. UL listed for wet and cold location. Operating temperature: -20C to +40C (-4F to + 104F)
• High output package: ideal for interior applications where the photometrical performance the 10W Xenon lamps is required. Equipped with NiMH battery, UL listed for operating temperature: +20C to +30C (+68F to +86F)

Enclosure

Durable cast aluminum housing is finished with textured polyester powder coat paint. The enclosure is gasketed for use in wet locations.

Finish

Available in four colors: off white, black, platinum gray and dark bronze.

Servicing

Lead-Calcium Models have a red LED that indicates AC power is on. The Nickel Metal Hydride Models have a bi-color LED indicates battery state of charge, test activation and four-state diagnostic status. Units are provided with a manual test switch that allows for quick operational check of the entire system.

Lighting Heads

Emergency mode utilizes Xenon wedge base T3-1/4 lamps available with in 6 and 12 watt versions. The LED lamp for normal lighting utilizes one five-watt white LED supplied with a simple and robust ballast circuitry. Normally on AC input: dual voltage 120/277Vac, 0.04A, 5W. The normally on LED lamp has an operational life of 50,000 hours(till 70% of initial light level)

Mounting Ability

The unit can be installed on various junction boxes with a universal mounting pattern, and can also accept a surface mount cable via the rigid conduit entry provision on the top of the unit

Housing Material

Die-Cast Aluminum with UV stabilized polycarbonate lens.

Temperature Rating

• With Lead-Calcium battery.+20C to +30C (+68F to +86F).
• With Exterior package: -20C to +40C (-4F to + 104F)
• High output package: +20C to +30C (+68F to +86F) Equipped with NiMH Battery

9.5" tall x 6.6" wide x 2.9" deep

Power Input

120/277 Vac, 60 Hz., 0.11/0.05 Amp for Emergency unit only. With optional 5w LED for normal lighting use: dual voltage 120/277Vac, 0.04A, 5W. Optional Remote Version is 6Vdc or 12Vdc.

Transfer

Automatically and instantly energizes lamp load upon failure of AC supply.

LVD

Low voltage battery disconnect circuit automatically shuts down lamp load and circuitry when battery reaches 87-1/2% discharge, preventing deep discharge and permanent damage to the battery.

Brownout

Close tolerance electronic circuit activates emergency unit when utility power dips below 80-85% of nominal voltage.

Charger

The pulse plus charger circuit utilizes a micro-controller which samples the battery in relation to its temperature, state of charge and input voltage fluctuations. The charger is current limited, temperature compensated short-circuit proof and reverse polarity protected. Charge regulation +/-1%. The equipment is capable of full recharge in compliance with UL 924 specifications.

Transformer

120/277 VAC

Controls

Sealed push-to-test switch, indicator light for AC On and fault indicator (flashes). Nickel Metal Hydride Models have bi-color LED indicates battery state of charge, test activation and four-state diagnostic status.

Applications

• Office Space
• Retails
• Institutional
• Hospitality
• Design/Build
• Also suitable for Wet or Cold Environments

Illumination Source

Xenon wedge base T3-1/4 in 6v or 12v and 6w or 10w, Optional second circuit for normally on conditions utilizes high power 5w White LED.

Battery Type

Sealed Lead Calcium, Nickel Metal Hydride

Performance Testing

Manual push-to-test switch, indicator light for AC-On. Optional Self Diagnostics system. This charger is a self-test and self-diagnostic charger. It will monitor and indicate any of the following failures: battery disconnect, battery, charger and lamp failures. The unit will perform a periodical self-test, of minimum 30 seconds every 30 days, 30 minutes every six months and 90 minutes annually. Discharge test can also be initiated manually.

Maintenance

Battery is maintenance free. Diagnostic circuitry continuously monitors every critical function of the unit. If a problem occurs, a single fault indicator on the outside of the fixture flashes immediately. A detailed diagnostic display is located internally. The detailed display will further indicate the nature of the fault as either a battery fault, load fault or a charger fault. Fully gasketed front provides access to battery and charger.

Unit is designed to be back mounted to wall surface via 4 fasteners.

Electrical Connections

1. Turn off building electrical emergency circuit
2. Remove the backplate by inserting a flat head screwdriver into the tab located on the top, and twisting.
3. Locate the quick connect connector, on the housing and disconnect it and put aside.

4. For standard junction box mounting, knock out the desired hole pattern in the backplate. Make the proper connections to unswitched building electrical emergency circuit. Route the quick connect through the large knockout and mount the backplate to the junction box.

   For Conduit entry mounting: Remove plug on the back plate and knock out the desired hole pattern in the back plate to secure the unit on the wall if required. Install the conduit and supply wires. For wet location: install a liquid tight fitting with teflon tape. Take wire nuts provided with the units. Bigger wire nuts might interfere with internal components. Attach to the unswitched building electrical emergency circuit.

5. Make the proper connections. 120 VAC - Connect the black (120 VAC), white (neutral) and ground(green) leads to the building utility. Insulate orange wire.

   277 VAC - Connect the orange (277 VAC), white (neutral) and ground(green) leads to the building utility. Insulate black wire.

   Remote - Connect the red (+) and the blue (-) leads to the DC input voltage of building utility. DC input voltage is indicated on the unit. It has to be compatible with the building electrical emergency circuit.

6. Place the quick connect in the slot and lock in place with the latch
7. AC must be off when mating quick connect. Mate the AC connector on the unit with the connector from the building AC service. Take the Housing and make sure the battery is connected to the board.
8. Reinstall the housing on the back plate. The housing is aligned to the pack plate with the two guides pin. In order to ensure proper snaps, maintain the housing parallel to the wall. Press together until it snaps. If it doesn't snap properly, try again making sure you maintain housing parallel to the wall. For conduit entry mounting, make sure the wire nuts provided with the unit have been used. Bigger wire nuts might interfere with internal components.
9. Energize AC. The AC pilot indicator, located under the cover, will illuminate.
10. For Self Diagnostics and Remote Monitoring installation instructions, see product data install sheet.

Time Delay

This option is used in areas where metal halide or mercury vapor lights are present, or lighting systems that lapse before startup. Intervals available are: 5, 10, or 15 minutes

• Commercial Interior or Exterior
• Offices
• Institutional
• Healthcare

UL Listed, ADA Compliant, Exterior Package Models are UL Listed for cold outdoor/wet locations. (-4F to +104F)

Entire unit (excluding lamps and fuses) carries a 3-year Full Warranty. The battery has a, 3-year Full Warranty, plus 3-year pro rata warranty